+86-18157128672

周一至周五

8:00~18:00

联系我们

全国统一服务热线:

+86-18157128672

客服QQ:3443748160

王先生:18258890703(微信同号)

洪先生:+86-18157128672(微信同号)

地址:杭州市西湖区西园九路8号A402

7.0寸群创液晶屏
您现在的位置:首页 > 工业液晶屏 > 群创液晶屏 > 7.0寸 >
  • LSA40AT9001
  • LSA40AT9001
  • LSA40AT9001
  • 型号:AT070TN94
  • 品牌:Innolux
  • 尺寸:7.0 inch
  • 分辨率:800 × 480
  • 典型亮度:400 cd/m² typ. (320 min.)
  • 典型视角:70°/70°/50°/70° typ.; CR ≥10
  • 接口:18/24-bit parallel RGB; 50-pin FPC
  • 温度额定值:−30 to +85°C; absolute rating, p.5
  • 规格版本:Final Ver.01, 2023-11-18
  • 询价与资料核对
技术参数

Innolux AT070TN94 7-inch RGB LCD | Ver.01 Specifications

AT070TN94 is a 7.0-inch, 800 × 480 a-Si TFT LCD module with parallel digital RGB input. The data below are checked against one identified manufacturer specification.

Specification basis: Innolux AT070TN94 LCD Module Specification, Final Ver.01, 2023-11-18. Page review: 2026-10-22. Page references below use the document’s printed pages 1–22; these follow three front-matter pages in the supplied PDF. Match the delivered module and revision before design approval.

Display and mechanical specifications

ParameterSpecificationSource pages
Model / manufacturerAT070TN94 / Innolux Display CorporationCover; 1
Diagonal / pixels7.0 inch; 800 × 480 pixels, RGB stripe (800 × 3 RGB subpixels × 480)1
Display technology / modea-Si TFT active matrix; TN; normally white, transmissive1; 20
Surface / view directionAnti-glare; 6 o’clock reference viewing direction1; 20
Active area, W × H154.08 × 85.92 mm1
Module, W × H × D164.9 × 100.0 × 5.7 mm nominal; use mechanical drawing for tolerances and FPC geometry1; 20
Dot pitch / pixel pitch0.0642 × 0.1790 mm / 0.1926 × 0.1790 mm (W × H)1; 20
Mass154 g typical1
Driver ICs / inversionEK79713 source driver; EK73202 gate driver; 1+2 dot inversion1; 20
Power consumptionPanel: 0.226 W typical; backlight: 1.674 W typical1

Parallel RGB interface and connector

The signal assignment provides 24 parallel RGB data inputs; Note 2 also specifies 18-bit RGB operation. It does not describe an LVDS input. Use the complete pin map and host timing for cable or controller selection.

ItemDocument-backed requirementSource pages
Interface18/24-bit parallel digital RGB; 50-pin FPC, 0.5 mm pitch2–4; 20
Recommended mating connectorHirose FH12A-50S-0.5SH2; 20
18-bit inputGround R0/R1, G0/G1 and B0/B1 (the two low bits of each channel)3, Note 2
Clock edgeLatch data on the falling edge of DCLK3, Note 3
DE modeMODE=1; VS and HS high3, Note 1
SYNC modeMODE=0; DE grounded3, Note 1
Reset / ditheringRESET active low; DITHB=1 disables and DITHB=0 enables internal dithering4
PinsSignals / function
1–2 / 3–4LED+ anodes / LED− cathodes
5 / 36 / 38 / 48GND
6 / 46VCOM
7DVDD
8 / 9 / 10 / 11MODE / DE / VS / HS
12–19B7 through B0
20–27G7 through G0
28–35R7 through R0
37DCLK
39 / 40L/R / U/D scan controls
41 / 42 / 43VGH / VGL / AVDD
44 / 47RESET / DITHB
45 / 49 / 50NC; no connection

Pin summary: printed pages 2–4. Follow the full FPC drawing and scan-control definitions for connector orientation and board implementation.

Optical specifications

Specified optical conditions: DVDD=3.3 V, backlight current=180 mA and ambient temperature=25°C. Measurements are made in a dark room after 30 minutes of operation; see printed pages 14–17 for geometry and definitions.

ParameterMinimumTypicalMaximumCondition / reference
Luminance320 cd/m²400 cd/m²Not specifiedCenter; pp.14–16
Contrast ratio400:1500:1Not specifiedNormal direction; p.14
Viewing, left / right / up / down60° / 60° / 40° / 60°70° / 70° / 50° / 70°Not specifiedCR ≥10; pp.14–15
Response time, TON+TOFFNot specified25 ms50 msWhite/black transitions; pp.14,16
White chromaticity, Wx0.260.310.36CIE 1931; p.14
White chromaticity, Wy0.280.330.38CIE 1931; p.14
Luminance uniformity70%75%Not specified9-point minimum/maximum; pp.14,17

Recommended operating electrical conditions

Rail / signalMinimumTypicalMaximumSource / condition
DVDD3.0 V3.3 V3.6 Vp.6; match host logic voltage
AVDD10.2 V10.4 V10.6 Vp.6
VGH15.3 V16.0 V16.7 Vp.6
VGL−7.7 V−7.0 V−6.3 Vp.6
VCOM2.6 V3.6 V reference4.6 Vp.6; optimize for each LCM
Logic high, VIH0.7 × DVDDNot specifiedDVDDp.6
Logic low, VIL0 VNot specified0.3 × DVDDp.6
Driver currentMinimumTypicalMaximumMeasurement rail
IGH0.05 mA0.2 mA1.0 mAVGH=16.0 V
IGL0.05 mA0.2 mA1.0 mAVGL=−7.0 V
IDVDD1 mA4.0 mA10 mADVDD=3.3 V
IAVDD5 mA20 mA50 mAAVDD=10.4 V

Current conditions: printed p.7. The module uses multiple supply rails; 3.3 V describes DVDD, not a complete single-supply module specification. Apply DVDD and VGL before VGH. Follow the complete power-on/off timing diagrams on pp.9–10.

LED backlight

ParameterMinimumTypicalMaximumSource / definition
Backlight voltage8.4 V9.3 V10.2 Vpp.7–8; at 25°C, 180 mA
Backlight current170 mA180 mA200 mAp.7; whole backlight
LED life20,000 hNot specifiedNot specifiedpp.7–8; minimum to 50% initial luminance at 25°C, 180 mA

LED power is applied through pins 1–4. The 20,000-hour figure is a defined luminance-life value, not a warranty. Lifetime can decrease above 180 mA. Confirm the backlight-driver design for the actual assembly.

Timing reference

ItemSpecified referenceSource
Typical DCLK frequency33.3 MHzp.12
Frame rate60 ±5 Hzp.12
Horizontal active / typical total800 / 1056 DCLKp.12
Vertical active / typical total480 / 525 linesp.12

Use the complete AC and input-timing requirements on pp.11–13. The document’s DCLK cycle-time and frequency endpoint tables do not fully correspond; confirm endpoint operating combinations with the manufacturer rather than deriving a new guaranteed range.

Absolute ratings and environmental qualification

The following limits are listed in the specification’s Absolute Maximum Ratings table (p.5). They are not substitutes for the recommended electrical settings above.

ItemMinimumMaximum
DVDD−0.3 V5.0 V
AVDD6.5 V13.5 V
VGH−0.3 V40.0 V
VGL−20.0 V0.3 V
VGH−VGLNot specified40.0 V
TOP, operation temperature−30°C85°C
TST, storage temperature−30°C85°C
LED forward current, each LEDNot specified25 mA
LED reverse voltage, each LEDNot specified1.2 V

Reliability tests on p.18 include high-temperature operation at panel-surface temperature Ts=85°C for 240 hours, low-temperature operation at ambient Ta=−30°C for 240 hours, and operation at +60°C/90%RH for 240 hours. The 85°C condition is not an unconditional guarantee for ambient temperature or all optical performance in finished equipment.

The documented vibration test is 1.5G, 10–55–10 Hz, 2 hours per X/Y/Z direction; mechanical shock is 100G/6 ms. These component test conditions do not establish automotive certification, finished-system qualification or warranty coverage.

Packaging reference

ItemSpecificationSource
Quantity50 modules/carton, 2 rows × 25p.21
Carton dimensions525 × 362 × 250 mmp.21
Total packed mass10.65 kg ±5%p.21

Packaging is the reference configuration in this document. Confirm actual shipment packing, quantity and current commercial terms with the quotation.

Compatibility review and quotation

Send the complete panel label and revision, controller/cable information, required quantity, destination and application conditions. Compare the parallel RGB pin map, all power rails, backlight drive, timing and mechanical drawing before approving a substitute. Current production and stock status are confirmed separately from this 2023 specification.

Request AT070TN94 technical review and quotation

Frequently asked questions

What interface does AT070TN94 use?

The Ver.01 pin assignment identifies parallel digital RGB with R0-R7, G0-G7 and B0-B7 data, plus DCLK, HS, VS and DE. For 18-bit input, ground the two low bits of each color channel. The recommended connector is Hirose FH12A-50S-0.5SH.

What are the typical viewing angles?

At contrast ratio CR ≥10, typical left/right/up/down viewing angles are 70°/70°/50°/70°. The respective minimum values are 60°/60°/40°/60°, under the optical test conditions in the specification.

What does the 20,000-hour LED life figure mean?

It is the specified minimum time until luminance falls to 50% of its original value at ambient 25°C and backlight current 180 mA. It is not a product warranty; operating above 180 mA can reduce lifetime.

Does the specification confirm current supply or replacement compatibility?

Current production, stock, price and order terms must be confirmed separately. A replacement requires the complete model/revision, RGB pin map, power rails, backlight drive, timing and mechanical fit to be checked in the actual equipment.

Related engineering resources

AT070TN94 replacement guide · AT070TN83 V.1 comparison record · 7-inch size and interface selection · AT070TN83 replacement workflow · Industrial LCD buying guide · Industrial LCD interface comparison · Industrial HMI application requirements

相关产品
官方微信

联系我们

公司地址:杭州市西湖区西园九路8号A402

公司电话:+86-18157128672

洪先生:+86-18157128672(微信同号)

王先生:18258890703(微信同号)

Email:market@hzxuhong.com

版权所有©2017 杭州旭虹科技有限公司 浙ICP备17024944号 工业显示器 | 工业液晶屏 | tft lcd | 友达液晶屏选型表 | 奇美液晶屏选型表 |