AUO G156HAN04.0 15.6-inch FHD High-Brightness LVDS LCD Panel
G156HAN04.0 is a 15.6-inch Full HD TFT-LCD module with a 1920 × 1080 resolution, AHVA normally-black display mode and dual-channel LVDS connectivity. The reviewed G156HAN04.0 (001) specification lists 1000 cd/m² typical luminance and an included LED backlight driver. It can be evaluated for industrial HMI and embedded displays requiring a high-brightness 16:9 panel.
Version scope: the specifications below apply to the supplied G156HAN04.0 (001), Final Specification Rev. 1.3, dated 22 November 2024. Do not assume that every G156HAN04.0 unit, suffix or earlier production revision has identical mechanical or backlight connections. Confirm the full label and applicable drawing before ordering or connecting a replacement.
Display and mechanical specifications
| Item | Reviewed specification: (001), Rev. 1.3 |
| Size / resolution | 15.6-inch / 1920 × 1080 pixels (FHD), 16:9 |
| Display mode | AHVA, normally black |
| Active area (H × V) | 344.16 × 193.59 mm |
| Pixel pitch | 0.17925 × 0.17925 mm; RGB vertical stripe |
| Outline including bracket | 363.8 × 215.9 mm typical; length 363.3-364.3 mm, width 215.4-216.4 mm |
| Thickness at PCB | 10.51 mm typical; 11.01 mm maximum. Check the mechanical drawing for local clearances and tolerances. |
| Module weight | 850 g maximum |
| Display colors / input | 16.7 million colors (RGB 8-bit), as stated in the reviewed specification |
| Interface | Dual-channel LVDS, 8-bit input |
| Surface treatment | Anti-glare, 3H hardness |
| Operating temperature | -30 to +85°C, specified for the panel surface |
| Storage temperature | -30 to +85°C; observe the humidity and non-condensation limits |
Optical performance
Values below are specified under stable conditions at 25°C. White luminance is measured at ILED = 70 mA. Typical values are not minimum guarantees.
| Item | Value / condition |
| White luminance | 800 cd/m² minimum; 1000 cd/m² typical |
| Nine-point luminance uniformity | 75% minimum; 80% typical |
| Contrast ratio | 700:1 minimum; 1000:1 typical |
| Response time | 25 ms typical; 35 ms maximum, rising + falling |
| Viewing angles | 80° minimum / 89° typical in each direction (left, right, up and down), at contrast ratio ≥ 10 |
| White chromaticity | CIE 1931: x = 0.313, y = 0.329, typical |
The optical table lists 72% typical color gamut without explicitly identifying the reference gamut. This page does not convert that figure into an unverified sRGB or NTSC coverage claim. Confirm color requirements with the applicable manufacturer documentation.
Power, connectors and backlight
| Item | Reviewed value |
| Logic supply (VDD) | 3.0 V minimum / 3.3 V typical / 3.6 V maximum |
| LCD power, excluding backlight | 1.75 W typical / 2.11 W maximum; see the electrical table and pattern-dependent measurement notes |
| LCD input current | 0.53 A typical / 0.64 A maximum |
| LVDS connector | 30-pin; P-TWO 187034-3009 or STM MSBKT2407P30HB as listed in the document. Verify the supplied connector and mating cable. |
| Backlight driver connector | 8-pin STM MSB24038P8D or compatible; mating model P24038P8 or compatible |
| Backlight supply | 10.8 V minimum / 12 V typical / 13.2 V maximum |
| Backlight power | 25.14 W typical / 30.17 W maximum at VLED = 12 V and ambient temperature 25°C |
| Backlight dimming | PWM, 200 Hz to 20 kHz; permitted duty range depends on frequency. Follow the complete control-signal requirements. |
| Frame rate | 60 Hz typical |
The logic and backlight supplies are different circuits. Do not apply the 12 V backlight supply to the 3.3 V logic input. Verify LVDS odd/even channel mapping, the backlight enable and PWM signals, connector orientation and the specified power sequence before connection. Turn power off before inserting or removing cables.
Do not reuse a five-pin backlight cable based only on the base model name. This reviewed (001) specification identifies an eight-pin driver connector. Use the exact supplied unit's label, connector photos and applicable drawing to establish compatibility.
The LED lifetime table lists an estimated minimum of 50,000 hours at ambient temperature 25°C, defined as the time until brightness falls to 50% of its initial value. High temperature and humidity can shorten operating life. This is not a whole-system lifetime or warranty promise.
High-brightness application checks
1000 cd/m² typical panel luminance alone does not guarantee readability in direct sunlight. Evaluate cover-glass reflections, any touch overlay or bonding, installed viewing angles, ambient light and thermal performance. The -30 to +85°C operating range refers to the panel surface, not an unconditional outdoor ambient-temperature rating.
A complete outdoor display also needs suitable enclosure, ingress protection and system-level validation. Touch functionality requires a separately selected compatible touch panel and controller; it is not included merely because the LCD supports a high-brightness image.
Replacement checklist
- Confirm the full model identification, suffix and applicable document revision.
- Compare active area, outline, mounting points, PCB clearance and connector positions.
- Verify dual-channel LVDS wiring, bit depth, controller timing and power sequencing.
- Check the actual backlight connector, cable, supply capacity and dimming controls.
- Validate brightness, thermal limits and optical appearance in the finished equipment.
The reviewed document describes a polarizer change in its revision history. For replacements installed alongside existing displays, confirm the production revision and compare samples rather than assuming identical surface appearance. A matching size and resolution do not establish a drop-in replacement.
Packing and order confirmation
The packing section lists up to 16 modules per carton, a maximum carton weight of 13.2 kg and external dimensions of 450 × 375 × 319 mm. These are document reference values, not a confirmed shipping quotation. Verify actual carton weight, packing quantity and dimensions for the shipment.
For a quotation, provide the full model code, label and connector photos if replacing an existing unit, quantity, application, delivery country and required date. Request the applicable specification, mechanical drawing and any required traceability or compliance documents.
Request a G156HAN04.0 specification and quotation
AUO industrial LCD panels | AUO 15.6-inch LCD panels
Document basis
Reviewed on 30 September 2026 against the supplied AUO G156HAN04.0 (001) Final Specification, Rev. 1.3, dated 22 November 2024. Main references: general specifications, page 8; optical characteristics, pages 9-11; electrical characteristics, pages 14-17; signal interface and timing, pages 19-23; mechanical drawings, pages 25-26; packing, page 28. This identifies the version reviewed, not the latest available revision or a guarantee that it applies to every unit bearing the base model name.
The document includes module reliability test conditions and compliance requirements. These do not replace a lot-specific test report, certification evidence or validation of the complete equipment.
