BOE BA104S01-100 10.4-inch SVGA LCD specifications
BA104S01-100 is a 10.4-inch BOE transmissive TFT-LCD module with 800 × 600 SVGA resolution, a normally white display mode and a 20-pin LVDS signal connection. The supplied BOE Chengdu final specification, Rev. 1 dated 12 December 2014, lists 500 cd/m² typical center luminance and an operating temperature range of −20 to +70 °C. Confirm the label and current specification for the module offered before approving a design or replacement.
Display and mechanical specifications
| Parameter | BA104S01-100 specification | PDF page |
|---|---|---|
| Manufacturer / model | BOE Chengdu Optoelectronics Technology Co., Ltd. / BA104S01-100 | 1, 12 |
| Screen size / resolution | 10.4 inches; 800 × 600 pixels (SVGA); RGB vertical stripe | 4–5 |
| Display mode / colors | Normally white, transmissive; 262K colors with 6-bit RGB input or 16.7M dithered colors with 8-bit RGB input | 4–5, 15 |
| Active area / pixel pitch | 211.2 × 158.4 mm; 0.264 × 0.264 mm | 5 |
| Module outline / weight | 236 × 176.9 × 5.6 mm nominal; 288 g typical. Use the mechanical drawing for tolerances and cable position. | 5, 21 |
| Center luminance | 500 cd/m² typical; 450 cd/m² minimum under the stated optical test conditions | 17 |
| Viewing angle, left/right/up/down | 70°/70°/60°/70° typical at contrast ratio > 10 | 17 |
| Contrast / response time | 800:1 typical; 30 ms typical rise plus fall | 17 |
| Operating / storage temperature | −20 to +70 °C operating; −30 to +80 °C storage | 6 |
Signal, power and backlight
| Parameter | BA104S01-100 specification | PDF page |
|---|---|---|
| LCD signal interface | 20-pin LVDS; STM MSB24013P20 or compatible connector. Compare the complete pin assignment and connector orientation. | 15 |
| 6/8-bit select | Pin 20 (SEL68): high selects 8-bit LVDS input; low or unconnected selects 6-bit input. Pins 17–18 carry channel 3 for 8-bit input. | 15 |
| LCD logic supply | 3.3 V typical; specified input range 3.0–3.6 V | 7 |
| Power consumption | LCD 1.6 W; backlight 2.484 W; total 4.084 W (document values) | 7 |
| Backlight | Top-edge LED lighting bar with a separate backlight supply. Verify the actual lead, connector and driver against the supplied drawing. | 5, 7, 21 |
| Signal timing | DE-only operation; 800 × 600 active pixels; typical pixel clock 39.6 MHz in the supplied timing table | 12 |
How to select BA104S01-100
Consider BA104S01-100 when a 10.4-inch SVGA display with a specified 500 cd/m² typical center luminance suits the project. The datasheet lists medical and industrial applications, but suitability for a particular enclosure, lighting condition or regulatory use requires system-level review. A luminance rating alone does not establish sunlight readability.
For a replacement, compare the full rear-label model and revision, 20-pin LVDS pinout, 6/8-bit selection on pin 20, DE timing, logic power, LED driver, connector positions, outline and mounting drawing. Matching screen size and resolution do not establish electrical or mechanical interchangeability. The BOE BA104S01 selection guide compares BA104S01-100 with BA104S01-200 and BA104S01-300.
Frequently asked questions
How bright is BA104S01-100?
The supplied Rev. 1 specification lists 500 cd/m² typical and 450 cd/m² minimum center luminance under its optical test conditions. Evaluate readability with the actual cover glass, backlight drive and ambient lighting.
What interface and color depth does it use?
It uses a 20-pin LVDS signal connector. Pin 20 selects 8-bit input when high and 6-bit input when low or unconnected; the specification describes 16.7M dithered colors or 262K colors respectively.
Can BA104S01-200 or BA104S01-300 replace BA104S01-100 directly?
Direct replacement is not established. The three versions share a nominal 10.4-inch SVGA format, but the supplied specifications differ in LCD pin assignment and backlight connection. Check both current datasheets and drawings before changing the cable or power design.
Is a touch panel included?
The reviewed BOE specification describes the LCD module and backlight; it does not establish an integrated touch panel. Request the complete touch assembly part number, drawing and controller details if touch input is required.
Does the 2014 specification confirm current production or stock?
No. The document describes a historical module revision. Confirm the exact offered label, applicable current datasheet, stock, lead time and quantity with the supplier.
Specification basis: BOE Chengdu 10.4SVGA Module Product Specification, CS3-PI-S744, Final Rev. 1, 2014-12-12. Page numbers above are the document’s printed pages. Values retain the document’s minimum and typical meanings.
For an engineering review or quotation, send the full installed label or required model, application, quantity, controller and cable details, and the current mechanical drawing. Request BA104S01-100 details.
