AUO A070VTN06.1 7-inch 1250-nit Parallel RGB TFT-LCD

  • AUO A070VTN06.1 7-inch 1250-nit Parallel RGB TFT-LCD
  • AUO A070VTN06.1 7-inch 1250-nit Parallel RGB TFT-LCD
  • Model:A070VTN06.1
  • Brand:AUO
  • Size:7.0"
  • Resolution:800×480
  • Brightness:1250 cd/m²
  • Perspective:60/60/40/60 (Typ.)
  • Interface:RGB (1 ch, 4-bit)
  • Operating Temp.:-20 to +70 °C
  • Production State:Discontinued
  • Request a Quote
  • Technical Parameters
  • AUO A070VTN06.1 7-inch 1250-nit Parallel RGB TFT-LCD

    AUO A070VTN06.1 is a 7.0-inch high-brightness TFT-LCD module with 800 x 480 WVGA resolution, 16-bit parallel RGB input and 1250 cd/m2 minimum center luminance. It is a normally-white panel with a 6 o'clock gray-inversion direction.

    This is a legacy discontinued model. The information below is retained for maintenance, identification and replacement engineering and was reviewed against AUO final specification version 0.8 dated June 8, 2018.

    Model control: Use the complete model A070VTN06.1. This is a non-touch, 51-pin parallel-RGB module with multiple panel supply rails. It is not an LVDS display and should not be substituted based only on its 7-inch size and 800 x 480 resolution.
    Lifecycle notice: A070VTN06.1 is listed as discontinued. Existing stock, refurbished units and broker inventory may vary in revision and condition. Confirm the rear label, date code, electrical condition and warranty before purchase. A replacement should be selected only after a full mechanical and electrical comparison.

    Reviewed Product Specifications

    Manufacturer / ModelAUO / A070VTN06.1LifecycleDiscontinued / legacy support
    Module typeTFT-LCD module, no touchDisplay size7.0 inch
    Resolution800 x 480 (WVGA)Display modeNormally white
    Brightness1250 cd/m2 minimumContrast ratio400:1 minimum, 500:1 typical
    Viewing angleTop 40 / bottom 60 / left 60 / right 60 degrees typical at CR 10Response time25 ms typical, 50 ms maximum
    Display colors65K colorsRGB interface16-bit parallel RGB
    Active area154.08 x 85.92 mmDot pitch0.0642 x 0.179 mm
    Outline dimensions166.43 x 102.2 x 6.3 mm, excluding FPCViewing direction6 o'clock gray inversion
    Main connectorHirose FH26W-51S-0.3SHW(05)Connector format51-pin FPC, 0.3 mm pitch
    Timing modesDE or SYNC mode, 60 Hz typicalScan controlHorizontal and vertical scan selection
    Panel power railsVDD 3.3 V, AVDD 11 V, VGH 16 V and VGL -7 V typical; correct sequencing is required
    Backlight27 LEDs, three strings of nineBacklight life10,000 hours minimum at 195 mA and 25 degrees C
    Reviewed operation tests-20 degrees C ambient / +70 degrees C panel surface, 240 hoursReviewed storage tests-30 to +80 degrees C, 240 hours
    Temperature clarification: The reviewed specification does not state a general -30 to +85 degrees C operating rating. Its reliability table records low-temperature operation at -20 degrees C ambient and high-temperature operation at +70 degrees C panel surface. Do not publish -30 to +85 degrees C operation without a separate controlled AUO document.

    High-Brightness Optical Performance

    The specification lists 1250 cd/m2 as the minimum center brightness after 15 minutes of operation at 195 mA backlight current and 25 degrees C. This high luminance can support evaluation for bright environments, but it does not by itself certify sunlight readability.

    Final readability depends on reflections, cover-lens transmission, optical bonding, polarizers, enclosure shading and ambient illumination. Test the complete display assembly under the intended lighting conditions.

    51-pin Parallel RGB Integration

    A070VTN06.1 uses a 51-pin 0.3 mm-pitch FPC connector and 16-bit parallel RGB data: five red bits, six green bits and five blue bits. The interface also includes pixel clock, data enable, horizontal/vertical sync, mode selection, scan-direction control and reset.

    1. Confirm the FPC contact direction, connector footprint and pin-1 orientation.
    2. Match the 16-bit RGB data order, falling-edge data latch and selected DE or SYNC timing mode.
    3. Provide all required VDD, AVDD, VGH and VGL rails within their specified ranges.
    4. Implement the complete documented power-on and power-off sequence; incorrect sequencing can permanently damage the module.
    5. Keep reserved pins unconnected and follow the recommended reset circuit.

    Backlight Design

    The LED backlight contains 27 LEDs arranged as three strings of nine. The reference conditions are 195 mA total supply current, 26.55 V typical and 29.7 V maximum. The external LED-driver voltage capability must exceed the maximum specified LED voltage.

    The 10,000-hour minimum life figure is defined as the point at which brightness falls to 50% of its initial value under the specified 195 mA and 25 degrees C conditions. This is substantially shorter than many newer industrial modules and should be considered in replacement planning.

    Mechanical and Reliability Review

    The module outline is 166.43 x 102.2 x 6.3 mm excluding the FPC, with a 154.08 x 85.92 mm active area. Obtain the controlled drawing when checking bezel opening, FPC bend space, connector position and tolerances.

    The specification includes reliability tests for temperature, humidity, ESD, vibration and shock. These are module qualification conditions, not proof that the completed equipment is suitable for automotive, marine, military, heavy-machinery or other regulated service. End-product validation remains necessary.

    Replacement Checklist

    • Confirm the exact A070VTN06.1 revision and rear-label information.
    • Match the complete outline, active area, FPC geometry and connector contact direction.
    • Compare the 51-pin parallel-RGB pinout and 16-bit color mapping.
    • Verify VDD, AVDD, VGH and VGL rails and the required power sequence.
    • Match the three-string LED backlight current and voltage requirements.
    • Evaluate the replacement's brightness, viewing direction, contrast, temperature performance and backlight life.
    Replacement warning: A newer 7-inch 800 x 480 LVDS module is not a direct replacement for A070VTN06.1. An interface conversion board, new cable, power-supply redesign and mechanical changes may be required. Confirm compatibility with samples before production use.

    Availability and Legacy Support

    As a discontinued product, A070VTN06.1 availability is subject to remaining stock and unit condition. For a stock check or replacement review, provide rear-label photos, required quantity, present controller information, destination country and the original equipment application.

    Browse more AUO LCD panels or view the 7-inch LCD category.

    Frequently Asked Questions

    Is A070VTN06.1 still in production?    No. It is treated as a discontinued legacy model. Confirm any available unit's revision, condition and warranty before ordering.
    Is its brightness 1250 nits typical?    No. The reviewed specification lists 1250 cd/m2 as the minimum center brightness under defined measurement conditions.
    Does A070VTN06.1 use LVDS?    No. It uses a 16-bit parallel RGB interface through a 51-pin FPC connector.
    Can it operate from one 3.3 V supply?    No. The panel requires multiple rails, including VDD, AVDD, VGH and VGL, plus a separate high-voltage LED-backlight supply. Correct sequencing is essential.
    Is it certified as sunlight-readable or automotive grade?    The specification confirms high luminance and module reliability tests, but it does not provide those end-use certifications. Validate the completed system for its intended environment.
    Request an A070VTN06.1 stock check or replacement review:
       Email market@hzxuhong.com with the label photos and project requirements.

Datasheet and Drawing Request

Contact us to request the current datasheet and mechanical drawing for A070VTN06.1. Please include your application and required quantity so we can confirm the applicable revision.

Request A070VTN06.1 Datasheet

Complete your display assembly

Build a display assembly around your selected LCD panel. Explore touch panels, LCD controller boards and signal or backlight cables.

Touch panels and bonding

Review touch dimensions, host connection, cover glass and bonding requirements.

LCD controller boards

Match the host video output to the panel interface, timing and power requirements.

Signal and backlight cables

Confirm both connector ends, pin mapping, cable length and backlight connections.

We will review the selected panel, controller firmware, cable pinout, power and touch configuration before confirming the proposed assembly. Send your quantity, application, delivery country and required date.

Request a matched display assembly

Get In Touch

Request a Model-Specific Quote

Fields marked * are required. Confirm the model below and add your quantity, application and delivery country. Availability and lead time are confirmed for each enquiry.

  • Contact Us
  • Email: market@hzxuhong.com
  • Skype: hzxuhong
  • Whatsapp: +86-18157128672 
  • Tel:+86-18157128672
  • Address:A402, No. 8 Xiyuan 9th Road, Xihu District, Hangzhou, Zhejiang, China